Hey there! As a vacuum casting supplier, I've seen my fair share of issues with vacuum - cast parts, and one of the most common problems is cracking. In this blog, I'm gonna dive into the reasons behind cracking in vacuum - cast parts and share some tips on how to prevent it.
Reasons for Cracking in Vacuum - Cast Parts
1. Material - related Issues
First off, the material you choose for vacuum casting can have a huge impact on whether your parts crack or not. Different materials have different properties, like shrinkage rates, flexibility, and brittleness.
- Shrinkage: When the casting material cools down after the vacuum casting process, it shrinks. If the shrinkage is uneven, it can create internal stresses within the part. These stresses can be strong enough to cause cracks. For example, some resins shrink more in one direction than another. This anisotropic shrinkage can lead to warping and cracking, especially in parts with complex geometries.
- Brittleness: Some materials are just naturally brittle. They don't have much give, so even a small amount of stress can cause them to crack. If you're using a brittle resin for your vacuum - cast parts and they're subjected to any kind of impact or bending, cracks are likely to form.
2. Process - related Issues
The vacuum casting process itself can also be a culprit when it comes to cracking.
- Incomplete Degassing: During the vacuum casting process, it's crucial to remove all the air bubbles from the casting material. If there are air bubbles trapped inside the part, they can act as weak points. When the part is under stress, these weak points are more likely to crack. Sometimes, the vacuum pump might not be working properly, or the degassing time might be too short, leading to incomplete degassing.
- Rapid Cooling: Cooling the cast part too quickly can cause cracking. When a part cools rapidly, the outer layer solidifies faster than the inner layer. This creates a temperature gradient and internal stresses. As the inner layer continues to cool and shrink, it can pull on the already - solid outer layer, causing cracks to form.
3. Design - related Issues
The design of the part plays a significant role in its susceptibility to cracking.


- Thick - to - Thin Transitions: Parts with sudden changes in thickness are more prone to cracking. When there's a large difference in thickness between two areas of the part, the thicker section cools and shrinks more slowly than the thinner section. This difference in cooling rates can create internal stresses at the transition point, leading to cracks.
- Sharp Corners and Edges: Sharp corners and edges concentrate stress. When a part is under load, the stress is not evenly distributed, but instead, it builds up at these sharp points. This concentrated stress can easily cause cracks to initiate and propagate.
How to Prevent Cracking in Vacuum - Cast Parts
1. Material Selection
- Choose the Right Material: Select a material that has the appropriate properties for your application. If you need a part that can withstand impact, choose a more flexible resin. If dimensional stability is crucial, look for a material with low shrinkage. You can also consult with material suppliers to get their recommendations based on your specific requirements.
- Test the Material: Before starting a large - scale production run, it's a good idea to do some test casts with the chosen material. This allows you to check for any potential issues, such as shrinkage or brittleness, and make adjustments if necessary.
2. Process Optimization
- Proper Degassing: Make sure your vacuum pump is in good working condition and that you're allowing enough time for degassing. You can also use techniques like multiple degassing cycles or gentle agitation during the degassing process to ensure all the air bubbles are removed.
- Controlled Cooling: Instead of letting the cast part cool rapidly, use a controlled cooling process. You can place the part in an oven and gradually reduce the temperature over time. This helps to minimize the temperature gradient and internal stresses, reducing the risk of cracking.
3. Design Improvements
- Gradual Thickness Transitions: When designing your part, try to avoid sudden changes in thickness. Instead, use gradual transitions between thick and thin sections. This helps to distribute the stress more evenly and reduces the likelihood of cracking.
- Rounded Corners and Edges: Replace sharp corners and edges with rounded ones. Rounding the corners helps to distribute the stress more evenly, reducing the stress concentration and the risk of cracking.
Conclusion
Cracking in vacuum - cast parts can be a frustrating problem, but by understanding the reasons behind it and taking the right preventive measures, you can significantly reduce the occurrence of cracks. As a vacuum casting supplier, I'm always here to help you choose the right materials, optimize the casting process, and improve your part designs.
If you're interested in Vacuum Pressure Casting, we can offer high - quality vacuum - cast parts that are free from cracks and meet your specific requirements. Whether you're in the automotive, aerospace, or consumer products industry, I've got the expertise and resources to provide you with the best solutions.
If you're looking to purchase vacuum - cast parts or have any questions about the process, don't hesitate to get in touch. We can have a detailed discussion about your project and find the most suitable approach for you. Let's work together to create high - quality vacuum - cast parts that meet your expectations!
References
- "Handbook of Plastic Materials and Technology" by Irvin I. Rubin
- "Manufacturing Engineering and Technology" by Serope Kalpakjian and Steven R. Schmid